WEB CONTROL PRODUCTSUser ManualOpen Loop Tension ControllerTCD 600FORM NO. L-20348-F-0705
FORM NO. L-20348-F-070510TCD600 ISOLATED OUTPUTSChanging the Output Isolation Setting1. Disconnect all electrical power from the TCD600.2. Remove al
FORM NO. L-20348-F-070511GLOSSARY OF TERMSSonic Ultrasonic SensorProx Proximity SensorProx Encod Proximity Sensor-Encoder combinationCounts For Pr
FORM NO. L-20348-F-070512The front panel of the TCD 600 has nine function buttons and a two-line display (See Figure 11).The TCD 600 has a feature tha
FORM NO. L-20348-F-070513SETUP MODE - MACHINE SETUPNOTE: To gain access to Machine setup, press the Nexen logo button while simultaneously pressing th
FORM NO. L-20348-F-0705141. Press the minus button to select Set Job, then press Enter. The upper display line changes to Set Job and the lower disp
FORM NO. L-20348-F-0705158. The display returns to Set Job. Press EDIT again to edit JOB 2, and repeat this procedure up to JOB 5 if needed. Or, pr
FORM NO. L-20348-F-070516CALIBRATION MODE - (continued...)NOTE: The following procedure is for either the Proximity Switch system or the Proxi
FORM NO. L-20348-F-070517 SETUP MODE [Set Machine] Language: English * English Millimeters Inches Inches Wind Unwind Wind Sonic Pr
FORM NO. L-20348-F-070518QUICK REFERENCE SETUP AND CALIBRATION WORKSHEET
FORM NO. L-20348-F-070519 Unwind Applications, Prox Encod Sensor [Edit Job] (Parameters) Full Roll: 060.00 in Setpoint: 010.0 %
FORM NO. L-20348-F-07052In accordance with Nexen’s established policy of constant product improvement, the specifications contained in this manual are
FORM NO. L-20348-F-070520OVERVIEWThe TCD 600 is an open loop controller that maintains constant tension by changing its output as the d
FORM NO. L-20348-F-070521NOTE: A Job must be Loaded before operating the TCD 600. Once a Job is Loaded into memory, the TCD 600 will recall this Job o
FORM NO. L-20348-F-070522UNWIND APPLICATIONWith a full roll on the unwind shaft, the Start contact or button is momentarily closed or pressed to put t
FORM NO. L-20348-F-070523AC Power ... 115VAC/230VAC, 0.3A/0.6A, 50/6
FORM NO. L-20348-F-070524WARRANTYWarrantiesNexen warrants that the Products will be free from any defects in material or workmanship for a period of 1
FORM NO. L-20348-F-07053Table of ContentsINTRODUCTION ------------------------------------------------------------------------------------------------
FORM NO. L-20348-F-07054FIGURE 1The Nexen TCD 600 is a non-contact open loop tension control system that provides reliable web tension control that’s
FORM NO. L-20348-F-070557.25 In.[184 mm]FIGURE 5CAUTIONThe TCD 600 is an electronic component and should be mounted in a shock and vibration free area
FORM NO. L-20348-F-07056An Ultrasonic Sensor can measure the change in roll radius by bouncing soundwaves off the material, enabling the TCD 600
FORM NO. L-20348-F-07057CAUTIONObserve polarity when connecting any devices marked + and -.Refer to Figure 10A and 10B for all electrical
FORM NO. L-20348-F-07058FIGURE 10AELECTRICAL CONNECTIONS(TCD 600 Back Panel)ELECTRICAL CONNECTIONS (continued...)(continued...)5 6 7 8 9 10 1112
FORM NO. L-20348-F-07059TCD 600 ALARM OUTPUT CONNECTION DIAGRAMSFIGURE 10BELECTRICAL CONNECTIONS (continued...)29/3130/32TCD 600To PLC InputVDC C
Commentaires sur ces manuels